Scotsman CMS1002W Especificações

Consulte online ou descarregue Especificações para Soluções para fazer cubos de gelo Scotsman CMS1002W. Scotsman CMS1002W Specifications Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 22
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
INTRODUCTION
This manual is intended as a reference for the
installation of a Scotsman ice maker model
CMS1002.
TABLE OF CONTENTS
Page
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Environmental Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
For the Installer
Machine & Bin Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
For the Plumber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
For the Electrician . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Final Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Initial Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Service Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CMS1002W
September, 1993
Page 1
Vista de página 0
1 2 3 4 5 6 ... 21 22

Resumo do Conteúdo

Página 1 - CMS1002W

INTRODUCTIONThis manual is intended as a reference for theinstallation of a Scotsman ice maker modelCMS1002. TABLE OF CONTENTSPageSpecifications . .

Página 2

ADJUSTMENT OF THE TIMER & SWITCH ASSEMBLYOne complete revolution of the cam on the timerrepresents eight minutes. If left as factory set,four and

Página 3

COMPONENT DESCRIPTIONCompressor ContactorThe compressor contactor carries the compressorline current. The contactor is wired so any controlin the pilo

Página 4

COMPONENT DESCRIPTIONIce Level ControlThis electronic control uses sound waves tomeasure the distance between the bottom of theice machine and the top

Página 5

COMPONENT DESCRIPTIONElectric Water Inlet Valve The water inlet solenoid valve fills the reservoirassembly with water. Excess water overflows outthe o

Página 6

SERVICE SPECIFICATIONSWhen servicing a machine, it’s helpful to comparethat unit’s operating characteristics to those of anew, clean, normally operati

Página 7

CLEANING//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Página 8

CLEANINGSANITIZE WATER SYSTEM1. Remove and discard all ice from the bin.2. Remove front panel.3. Drain the reservoir4. Prepare 2 gallons of an approve

Página 9

SERVICE DIAGNOSISSYMPTOMPOSSIBLE CAUSEPROBABLE CORRECTIONNo ice, machine does not run 1. No electrical power 1. Restore power2. Circuit breaker trippe

Página 10

SERVICE DIAGNOSISSYMPTOM POSSIBLE CAUSE PROBABLE CORRECTIONLow ice production 4. High head pressure, a result of adirty condenser 4. Clean water circu

Página 11

CONDITION DETERMINE CAUSE PROBABLE CORRECTIONIce Machine does not run, it haspower to it, the high pressurecontrol is closed, the on/off switch isset

Página 12

SPECIFICATIONSAlways refer to the nameplate, located on the backof the cabinet, for the:••model number, ••serial number, ••basic electricalrequirement

Página 13

TRANSDUCER LOCATIONTRANSDUCERSOCKET IN ICEMACHINE BASEPLUGCONNECTIONREMOVAL OF TRANSDUCERREMOVAL AND REPLACEMENTTRANSDUCER1. Disconnect electrical pow

Página 14

REMOVAL AND REPLACEMENT /////////////////////////////////WARNING/////////////////////////////Disconnect electrical power before beginning.////////////

Página 15

REMOVAL AND REPLACEMENT /////////////////////////////WARNING//////////////////////////////////Disconnect electrical power before beginning.///////////

Página 16

FOR THE INSTALLER: Environmental LimitationsInstallation LimitationsThe ice making portion of this ice system isdesigned to be installed indoors, in a

Página 17

FOR THE INSTALLER: Machine & Bin AssemblyOverview:This ice system is comprised of 2 majorassemblies:1. The ice storage bin.2. The ice maker itself

Página 18

FOR THE PLUMBERWater SupplyThe recommended water supply line is a 3/8-inchO.D. tubing with a minimum operating pressure of20 PSIG and a maximum of 80

Página 19

FOR THE ELECTRICIAN: Electrical Connections See the NAMEPLATE for current requirements todetermine wire size to be used for electricalhookup. The cube

Página 20

FOR THE INSTALLER: Final Check List1. Is the ice maker cabinet in a room whereambient temperatures are within the minimum andmaximum temperatures spec

Página 21

INITIAL START UPIce Maker:1. Remove front panel by pulling out to unsnap.2. Remove two screws and the control box cover.3. Remove the evaporator cover

Página 22

INITIAL START UPAdjust for the correct size if needed:To produce SMALLER sized ice cubes: Locate cube size control knob, in the front of thecontrol bo

Comentários a estes Manuais

Sem comentários